View Full Version : Whats years and vehicles...
Iceman_19
08-08-2004, 01:21 PM
did the 4 bolt 350 come in?
CamaroRobZ28beer
08-08-2004, 01:53 PM
So many different years man, they came in vans and shit too. I got mine out of a van, same bore and stroke as anything. Lots of chev trucks had them you can tell in the vin if its a 350 or not. I forgot but maybe its K or an M in a ceertain place but i donno ask jason (79z28)
79 Z28
08-08-2004, 02:20 PM
did the 4 bolt 350 come in?
there were so many options/models etc practically 100's lol the only way to really find out if it is one cuz motors can be changed, special models etc. is to look at the motor physically with the pan off, or run the casting #
www.mortec.com will give you all the info
Iceman_19
08-08-2004, 11:37 PM
hmm well no luck there, since the motor is in a toyota truck, somehow i think the motor isnt stock in that truck. :D
79 Z28
08-09-2004, 11:26 AM
hmm well no luck there, since the motor is in a toyota truck, somehow i think the motor isnt stock in that truck. :D
yes, but the serial number on the block will tell you exactly what its out of and what it is from that site
Iceman_19
08-11-2004, 01:46 PM
ok, i found out what the motors from. he got it from a 76 GMC jimmy. where could i find some headers for this? also, intake, carb, etc.
79 Z28
08-11-2004, 01:54 PM
ok, i found out what the motors from. he got it from a 76 GMC jimmy. where could i find some headers for this? also, intake, carb, etc.
damn, i used to have all that stuff for sale, but not anymore :'(
Iceman_19
08-11-2004, 02:20 PM
you son of a bitch. ok, instead, just give me the motor out of your camaro and i put that in truck. :D
what would this motor have made for power and torque in stock form? (since its in stock form).
also, what size carb would be good for a 350?
79 Z28
08-11-2004, 02:30 PM
you son of a bitch. ok, instead, just give me the motor out of your camaro and i put that in truck. :D
what would this motor have made for power and torque in stock form? (since its in stock form).
also, what size carb would be good for a 350?
haha, my motor in my camaro is gonna cost to the tune of $9000 :'( id say about 190hp and 320 lb ft in pure stock trim. carb depends on what you want it for, a vacume secondary setup for street use for sure. id say 650-750 no more if your planning on intake/ exh etc, maybe a small cam eventually :)
Iceman_19
08-11-2004, 02:36 PM
well, its in a truck, and its going to be 4wheeled, so i want lots and lots of sexy torque. 38" tire smoking torque. :D
Iceman_19
08-11-2004, 02:41 PM
for a cam shaft im thinking the X4254H. its the xtreme 4x4 cam. 1000-5200 rpms, duration is 210/218 @.050, .447/.462 lift with 1.5 rockers, and 111 degrees lobe.
iroc22
08-11-2004, 07:36 PM
Try 1.6 RR, for better off-idle torque, you want low duration high lift cams. As far as carb goes, get a 4ME Rochestor carb, because the smaller primary venturis will provide better torque and when you need the power to spin the wheels a bit, the bigger secondary ones will give you that extra umph.
Iceman_19
08-11-2004, 11:10 PM
Try 1.6 RR, for better off-idle torque, you want low duration high lift cams. As far as carb goes, get a 4ME Rochestor carb, because the smaller primary venturis will provide better torque and when you need the power to spin the wheels a bit, the bigger secondary ones will give you that extra umph.
i was thinking about getting one of those holley truck avenger carbs, built for off-roading so they wont die at extreme angles and such. 670cfm carbs.
iroc22
08-12-2004, 09:41 AM
Try 1.6 RR, for better off-idle torque, you want low duration high lift cams. As far as carb goes, get a 4ME Rochestor carb, because the smaller primary venturis will provide better torque and when you need the power to spin the wheels a bit, the bigger secondary ones will give you that extra umph.
i was thinking about getting one of those holley truck avenger carbs, built for off-roading so they wont die at extreme angles and such. 670cfm carbs.
yeah those are pretty good as well, if you have the extra money to spend
Iceman_19
08-12-2004, 12:47 PM
i have drug money, much to go around!
79 Z28
08-12-2004, 01:54 PM
i have drug money, much to go around!
SHIT MAN HOOK ME UP, I NEED TO GET MY CAR DONE, I ONLY NEED A LITTLE BIT :D p.s. sorry about caps, too lazy to retype :P
Iceman_19
08-13-2004, 12:01 AM
yeah i wish i had drug money too.
vBulletin® v3.7.0 Beta 6, Copyright ©2000-2012, Jelsoft Enterprises Ltd.